Bass Pro Shops Xps Battery Charger Manual
Battery(s) are not charging, Blue AC Power Light Ring, RED Charging and Battery Type LEDs are On Confirm all charger cables are installed with the correct polarity connections at each battery, and that all connections are clean and tight. Confirm that there are no Bank Trouble Status LED indicators on. If they are check the battery and battery connections at the battery indicated on the unit. Note: Incorrect wiring will result in reverse polarity or high reverse voltage, in the event this happens, the XPSiT Charger has been designed to not fail as a result, however it will cause the charger to 'internally disconnect' and provide 'no output' until the (reverse polarity) caused by putting the 'Red' + lead on a - negative battery terminal)and/or the (high reverse DC voltage caused by taking one bank cable and spreading it across two batteries) is corrected, using the wiring diagrams as shown on pages 11-18.
Bass Pro Shops Xps Battery Charger Manual
With the charger on, read DC voltage at each battery. If any of the readings are less than 13 Volts DC proceed with the following: A.
See Through Engine S1 • E5 See Thru Engine on Turbo Nitro and Dyno (How much HP does it make?) - Duration: 18:04. Warped Perception Recommended for you. Hypersonic vst plugin is the one of the best plugin for fl studio and other music production,it contain many sample sound piano special for. Luxonix purity vst download free PURITY is a next generation of digital musical instrument workstation and PCM sound module software. Luxonix purity vst full free download. Luxonix purity free download - Purity, Purity, Facebook Purity, and many more programs. Our new desktop experience was built to be your music destination. Listen to official albums & more.
The ultralight Bass Pro Shops XPS Intelligent Technology Series On-Board Marine Battery Charger does everything but catch the fish! 4th generation XPS iT Series features Digital Intelligent Technology for extreme performance and ease of use. 5' AC and DC cable lengths.
Disconnect AC power at the 120VAC outlet. Go to pages 11-18 of this manual and confirm your XPSiT model charger is connected correctly as illustrated in the installation drawings. Upon Completing B above; Plug your charger into AC Power and observe the LED center. Charger should be in the charging Mode (Charge Status Indicator should be Red). If after completing a full charge cycle, 10-12 hours or more for deeply discharged or completely dead batteries, the Charge Status Indicator should be Green and the Go Fish! Indicator should be on as well as the Blue AC Power Light Ring.
I will give you my thoughts on your charger. Unless they have recently changed, the XPS chargers are made by Pro Mariner. Pro Mariner used to be a great charger, but like it seems everybody else is doing, they changed to Chinese built chargers. For years, I ran the Pro Mariner Pro Tourney three bank 30 amp chargers. Then they started failing. The first one that failed was under warranty so they were great about sending me another the next day. 
That one failed a couple months after the warranty ran out, I sent it in and they said the boards were out dated and couldn't be repair.
I have a degree in electronics and very good with it so I asked if they could just send it back and a copy of the schematic. They said they couldn't send me the schematic but offered me a credit toward a replacement, so I went with that. The replacement failed right after the warranty ran out, they said the boards were outdated and couldn't be repaired, 'again'. But they could offer me credit toward a new one. That's when I told them what they could do with their outdated, non repairable charger.
Bass Pro Shop Xps Charger
You know, that was about five years ago, and I never have called them back and told them they could pull it out. So, with that, I will just say I hope you have better luck with the XPS. I have been running an BPS charger since 2010. I have never had any problems with it. But I used to run a different brand on my old boat. Try this before you go any further. Disconnect the wires from each terminal, clean the terminals just like any battery, them clean each wire ring terminal.